• Jackson MS Sand Delivery - Mulch Mound
  • Jackson MS Sand Delivery - Mulch Mound
1 2
Sand - Mulch Mound
Sand - Mulch Mound

About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.
Nicole Sheehe
Nicole Sheehe
Google Review

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

One cubic yard of this sand covers about 324 square feet at a 1 inch depth, which is the typical install range for mortar work, paver joints, and pool base prep. For mortar mixing, order based on batch volume rather than area, since a mason crew will tell you their ratio. For paver joints or bedding, measure your square footage and figure closer to 1 to 2 inches depending on the joint width and base design.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

FAQs

Read all FAQs

Jackson Sand Delivery

Jackson Sand Delivery

4.7
137 reviews
$74.00 per Yard
$74.00
Sale Sold out
Shipping calculated at checkout.
Type
Size
Minimum of 3 Yard
Hand-picked local yards
4,000+ regional deliveries
Dedicated support
Why order through Mulch Mound

The best local sand, without the guesswork.

We hand-pick and partner with the best yards in your region, keep only the ones our buyers rate well, and back each load with our guarantee.

Mulch Mound Guarantee

If your sand isn't the quantity or quality you ordered, we'll make it right.

About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.
Nicole Sheehe
Nicole Sheehe
Google Review

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

One cubic yard of this sand covers about 324 square feet at a 1 inch depth, which is the typical install range for mortar work, paver joints, and pool base prep. For mortar mixing, order based on batch volume rather than area, since a mason crew will tell you their ratio. For paver joints or bedding, measure your square footage and figure closer to 1 to 2 inches depending on the joint width and base design.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

FAQs

Read all FAQs

View full details

How It Works

Getting started is easy — just follow these simple steps

1

Choose your quantity

Adjust the quantity to match your project. One cubic yard covers about 100 to 160 square feet at a 2 to 3 inch depth.

2

Select your delivery date

Select a delivery date you'd like for the product to be dropped off at your home

3

Sit back and wait

Sit back, wait, and let us work our magic to make sure the highest quality product is delivered to your driveway.

From The Mouths of Jackson Folks

4.7
out of 5 based on 137 reviews
Google Reviews
Nicole Sheehe
Nicole Sheehe

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

Google Review
Ryan Cully
Ryan Cully

First time going with this company for mulch and it was an efficient process from start to finish. Website was easy—I told them exactly where I wan...

Read full review

First time going with this company for mulch and it was an efficient process from start to finish. Website was easy—I told them exactly where I wanted the mulch put on my driveway, and it was delivered perfectly when I got home from work the next day. Best deal around when I compared it to competitors and I will definitely be becoming back.

Google Review

Complete Your Outdoor Project

Most sand orders in Jackson go out alongside paver base or chip stone for the structural layer underneath, with the sand reserved for joints or mortar. If you are doing pool coping or a paver patio, a load of paver base plus this mason sand covers both the foundation and the finish work in one delivery.

Jackson Soil Delivery
Jackson Mulch Delivery
Map of the sand delivery area around Jackson, Mississippi

Service area

Areas we deliver sand in Jackson, Mississippi

See All Locations
Mulch Mound Pro Tip

Mason sand's fine, uniform grain is what makes mortar workable enough to spread and tool cleanly, but that same fineness means it holds water. In Jackson's humid stretches, keep your pile covered with a tarp between mixing sessions, especially after a summer thunderstorm rolls through, or you will be fighting a soupy mix the next morning instead of a workable one.

Mulch Mound Pro Tip

A common mistake is using mason sand as paver bedding and expecting it to behave like a base material. It compacts less predictably than chip stone and can migrate or pump under freeze thaw cycles, which matters even in Jackson's mild zone 8a winters when a hard frost hits before November 10. If you are setting pavers, reserve mason sand for joint fill and use a proper base material underneath.

Mulch Mound Pro Tip

If your project mixes mortar and sets pavers, order mason sand for the mortar and joints and a separate load of chip stone or paver base for the structural layer, rather than trying to stretch one material across both jobs. It is a small extra delivery but it saves you from a bedding layer that will not hold up, and most crews around Jackson already order this way.

Working With Sand in Jackson

Jackson sits on heavy clay, and that clay does not drain the way a paver base or mortar bed needs to perform. Mason sand gives masons and hardscapers a clean, uniform material that is not fighting the native soil underneath it. With hardscape season running spring through fall here and plenty of humidity in between, workable mortar sand matters more than in drier climates, since a gritty inconsistent mix sets up wrong and cracks faster. This is also why more paver crews around the Old Capitol area have shifted to chip stone for bedding, since it locks in place and will not pump up through the joints the way sand can under Jackson's wetter stretches.

Masonry vs Fill Sand

Masonry sand is washed and finely screened, the right choice for mortar work, paver joints, and sandboxes. Fill sand is coarser and less processed, better suited to leveling, bedding pipe, and filling low spots.

Bedding and Leveling

For pavers, screed a 1 inch sand bed over a compacted base rather than using sand to fix deep grade problems. A thin, even bed locks pavers in place. A thick one shifts underfoot.

Working With Moisture

Slightly damp sand spreads, screeds, and compacts far more easily than bone dry sand, which just flows back into your screed lines. Lightly wetting the pile before you work it saves real effort.

Frequently Asked Questions

Click a question to see the answer

Answer

What is mason sand actually used for on a typical job here?

Mason sand is used for mixing mortar, filling paver joints, and building pool bases. It is finer and more uniform than concrete sand, which is what keeps mortar workable when you are laying brick or block. It is not meant to be your structural base layer under pavers, that job is better suited to chip stone or paver base.

Answer

How many cubic yards do I need for a paver patio's joint fill?

One cubic yard covers about 324 square feet at a 1 inch depth, but joint fill uses far less than that since you are only filling the gaps between pavers, not covering the whole surface. For most patios, a fraction of a yard handles the joints, so measure your square footage and order based on actual joint width and spacing.

Answer

When is the best time to schedule a mortar or paver project in Jackson?

Spring through fall is peak hardscape season here, with mild enough temperatures for mortar to cure properly before the first frost around November 10. Working in that window also avoids the summer humidity spikes that can make mason sand hold extra moisture and throw off your mortar mix ratio.

Answer

Where will the sand be placed on delivery day?

The driver places the load wherever you direct, typically a driveway, curb pad, or flat spot near your work area. Clear the space ahead of time and have a wheelbarrow ready if you need to move it further into the yard, since the truck cannot access every backyard directly.

Answer

Should I use mason sand or chip stone for my paver base?

For the structural base layer under pavers, chip stone is the better choice since it locks together and will not pump or shift the way sand can, especially given Jackson's clay soil and wetter seasons. Save mason sand for the joint fill on top, where its fine texture sweeps in cleanly between pavers.

More delivery around Jackson, Mississippi

All Jackson, Mississippi landscape supply