• Milwaukee WI Sand Delivery - Mulch Mound
  • Milwaukee WI Sand Delivery - Mulch Mound
1 2
Sand - Mulch Mound
Sand - Mulch Mound

About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.
Nicole Sheehe
Nicole Sheehe
Google Review

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

One cubic yard covers about 324 square feet at a 1 inch depth, and most mortar and bedding work only needs 1 to 2 inches. For a typical patio job, figure your square footage, divide by 324, then adjust up if you're going closer to 2 inches for a paver base or pool bed. Most residential jobs land between a half yard and two yards.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

A ton is approximately 2,000 pounds. Coverage varies by stone type and depth, but as a general guideline, one ton covers roughly 80-100 square feet at 2 inches deep.

FAQs

Read all FAQs

Milwaukee Sand Delivery

Milwaukee Sand Delivery

4.7
137 reviews
$74.00 per Yard
$74.00
Sale Sold out
Shipping calculated at checkout.
Type
Size
Minimum of 3 Yard
Hand-picked local yards
4,000+ regional deliveries
Dedicated support
Why order through Mulch Mound

The best local sand, without the guesswork.

We hand-pick and partner with the best yards in your region, keep only the ones our buyers rate well, and back each load with our guarantee.

Mulch Mound Guarantee

If your sand isn't the quantity or quality you ordered, we'll make it right.

About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.
Nicole Sheehe
Nicole Sheehe
Google Review

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

One cubic yard covers about 324 square feet at a 1 inch depth, and most mortar and bedding work only needs 1 to 2 inches. For a typical patio job, figure your square footage, divide by 324, then adjust up if you're going closer to 2 inches for a paver base or pool bed. Most residential jobs land between a half yard and two yards.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

A ton is approximately 2,000 pounds. Coverage varies by stone type and depth, but as a general guideline, one ton covers roughly 80-100 square feet at 2 inches deep.

FAQs

Read all FAQs

View full details

How It Works

Getting started is easy — just follow these simple steps

1

Choose your quantity

Adjust the quantity to match your project. One cubic yard covers about 100 to 160 square feet at a 2 to 3 inch depth.

2

Select your delivery date

Select a delivery date you'd like for the product to be dropped off at your home

3

Sit back and wait

Sit back, wait, and let us work our magic to make sure the highest quality product is delivered to your driveway.

From The Mouths of Milwaukee Folks

4.7
out of 5 based on 137 reviews
Google Reviews
Nicole Sheehe
Nicole Sheehe

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

Google Review
Ryan Cully
Ryan Cully

First time going with this company for mulch and it was an efficient process from start to finish. Website was easy—I told them exactly where I wan...

Read full review

First time going with this company for mulch and it was an efficient process from start to finish. Website was easy—I told them exactly where I wanted the mulch put on my driveway, and it was delivered perfectly when I got home from work the next day. Best deal around when I compared it to competitors and I will definitely be becoming back.

Google Review

Complete Your Outdoor Project

Most jobs pairing sand also need paver base or chip stone underneath it, since chip stone is increasingly replacing sand as bedding because it does not pump or wash out under Milwaukee's freeze thaw cycles. If you're mixing mortar for Cream City brick repair, you'll also want to have your cement and lime ratios sorted before the load arrives. Edging material and polymeric jointing sand are common add ons for finishing paver work.

Milwaukee Soil Delivery
Milwaukee Mulch Delivery
Map of the sand delivery area around Milwaukee, Wisconsin

Service area

Areas we deliver sand in Milwaukee, Wisconsin

See All Locations
Mulch Mound Pro Tip

For mortar work in Milwaukee, keep your sand covered and dry before mixing whenever possible, especially in spring when snowmelt and rain saturate everything. Wet sand throws off your water to cement ratio and weakens the mortar bond right when you need it strongest, before the next freeze thaw cycle sets in. A tarp over the pile for a day or two before use makes a real difference in workability.

Mulch Mound Pro Tip

A common mistake with paver joint sand is sweeping it in dry and calling it done. Compact it with a plate compactor and re-sweep at least twice, letting it settle into the joints fully. Skipping this step is why joints open up after the first Milwaukee winter, since freeze thaw cycling exposes any gaps you left behind.

Mulch Mound Pro Tip

If you're doing paver bedding rather than jointing, ask about chip stone instead. It has replaced traditional sand on a lot of Milwaukee driveways and patios because it locks together and resists the pumping action that pushes sand out from under pavers during freeze thaw seasons. Sand still makes sense for mortar and joints, just not always for the base layer anymore.

Working With Sand in Milwaukee

Milwaukee sits on silty clay that drains slowly, so sand plays a specific role here, it is not for filling low spots in the yard, it is for the precise work under and between pavers and in mortar joints. With clay soil already holding water against foundations, masons here lean on well graded sand to keep mortar workable and consistent, especially with the freeze thaw cycles between the May 10 last frost and the October 1 first frost putting real stress on joints. Pool installers around the city also spec it for smooth, stable bases before liners go down.

Masonry vs Fill Sand

Masonry sand is washed and finely screened, the right choice for mortar work, paver joints, and sandboxes. Fill sand is coarser and less processed, better suited to leveling, bedding pipe, and filling low spots.

Bedding and Leveling

For pavers, screed a 1 inch sand bed over a compacted base rather than using sand to fix deep grade problems. A thin, even bed locks pavers in place. A thick one shifts underfoot.

Working With Moisture

Slightly damp sand spreads, screeds, and compacts far more easily than bone dry sand, which just flows back into your screed lines. Lightly wetting the pile before you work it saves real effort.

Frequently Asked Questions

Click a question to see the answer

Answer

Is this the same as mason sand?

Yes, this is the finely screened, washed sand often called mason sand, it is finer and more uniform than concrete sand, which is exactly what makes it workable for mortar mixing. It is also used for paver joints and pool base prep. If someone local mentions mason sand, this is the product.

Answer

How much sand do I need for a patio joint job?

One cubic yard covers about 324 square feet at 1 inch deep, and joint filling is usually a thin layer, so a 300 square foot patio might only need a quarter to a half yard depending on joint width. Measure the actual joint area rather than the full patio footprint to avoid over ordering.

Answer

When should I install sand for a patio or pool base in Milwaukee?

Hardscape season here runs spring through fall, generally after the May 10 last frost and before the October 1 first frost. Working outside that window risks the ground being frozen or too saturated from snowmelt, which affects compaction and mortar workability. Most contractors book their heaviest sand orders from May through September.

Answer

Where will the sand be dropped off?

We place the load wherever you specify, typically a driveway or staging area with truck access, at the time you choose during checkout. Make sure the spot is clear and reachable by a delivery truck, since the material is dumped in bulk rather than carried in. Let us know ahead if access is tight.

Answer

Should I use sand or chip stone under my pavers?

Traditional sand bedding is increasingly being replaced by chip stone for paver bases, since chip stone locks together and resists pumping out, which is a real issue through Milwaukee's freeze thaw cycles. Sand is still the right call for mortar mixing and for filling joints between pavers. If you're unsure which fits your project, tell us the job and we can help you decide.

More delivery around Milwaukee, Wisconsin

All Milwaukee, Wisconsin landscape supply