About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

One cubic yard of this sand covers about 324 square feet at a 1 inch depth, so a small paver patio might only need a fraction of a yard while mortar mixing for a stone wall could run higher depending on the mix ratio. Install depth typically runs 1 to 2 inches, so double your square footage estimate if you are going for the full 2 inches. Since it is sold by the cubic yard, measure your project area first and work backward from there.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

Georgetown Sand Delivery

Georgetown Sand Delivery

4.7
137 reviews
Regular price $74.00 per Yard
Regular price Sale price $74.00
Sale Sold out
Shipping calculated at checkout.
Type
Size
Minimum of 3 Yard
Hand-picked local yards
4,000+ regional deliveries
Dedicated support
Why order through Mulch Mound

The best local sand, without the guesswork.

We hand-pick and partner with the best yards in your region, keep only the ones our buyers rate well, and back each load with our guarantee.

Mulch Mound Guarantee

If your sand isn't the quantity or quality you ordered, we'll make it right.

About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.

We had a great experience with mulch mound! Our mulch arrived when we requested. The delivery fee was so reasonable. We’ll use them again for sure!

One cubic yard of this sand covers about 324 square feet at a 1 inch depth, so a small paver patio might only need a fraction of a yard while mortar mixing for a stone wall could run higher depending on the mix ratio. Install depth typically runs 1 to 2 inches, so double your square footage estimate if you are going for the full 2 inches. Since it is sold by the cubic yard, measure your project area first and work backward from there.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

View full details

How It Works

Getting started is easy — just follow these simple steps

1

Choose your quantity

Adjust the quantity to match your project. One cubic yard covers about 100 to 160 square feet at a 2 to 3 inch depth.

2

Select your delivery date

Select a delivery date you'd like for the product to be dropped off at your home

3

Sit back and wait

Sit back, wait, and let us work our magic to make sure the highest quality product is delivered to your driveway.

From The Mouths of Georgetown Folks

4.7
out of 5 based on 137 reviews
Google Reviews

Complete Your Outdoor Project

Most jobs pairing this sand also need a base layer of crushed stone underneath, especially given Georgetown's silt loam subgrade, which does not drain as fast as sandy soil elsewhere. Pavers themselves and edge restraints usually round out the order. If you are doing mortar work, having extra sand on hand for touch ups after the first freeze thaw cycle saves a second delivery next spring.

Mulch Mound Pro Tip

Mason sand for paver joints should go down dry and get swept into the joints in stages, then compacted with a plate tamper between passes. If you pack it in wet from the start, it clumps and leaves voids under the surface that show up as settling a season later, especially once Georgetown's freeze thaw cycles start working on the base come November.

Mulch Mound Pro Tip

A common mistake here is ordering mason sand for a paver base instead of joint fill. Bedding layers under pavers are increasingly done with clean chip stone instead, since it does not pump or wash out the way sand can under Kentucky's heavier spring rains. Save the mason sand for the joints and mortar work where its fine, uniform texture actually earns its keep.

Mulch Mound Pro Tip

If you are working mortar for a stone wall or walkway edge, order slightly more sand than your mix calculator suggests. Small batches mixed on site always waste some material, and running short mid pour on a Saturday means a delayed project until the next delivery slot opens up.

Working With Sand in Georgetown

Georgetown sits on silt loam soil that holds water and compacts unevenly, which is exactly why mason sand matters for hardscape work here. Pavers and patio bases need a consistent, uniform bedding layer that does not shift the way the native silt loam does after a wet spring. With Zone 6b winters bringing freeze thaw cycles, a properly bedded paver joint filled with this sand resists heaving better than joints packed with whatever fines were left over from a driveway job. Around the horse farms and bourbon country properties here, a lot of the hardscape work is patios, walkways, and mounting blocks, all of which depend on sand that stays put.

Masonry vs Fill Sand

Masonry sand is washed and finely screened, the right choice for mortar work, paver joints, and sandboxes. Fill sand is coarser and less processed, better suited to leveling, bedding pipe, and filling low spots.

Bedding and Leveling

For pavers, screed a 1 inch sand bed over a compacted base rather than using sand to fix deep grade problems. A thin, even bed locks pavers in place. A thick one shifts underfoot.

Working With Moisture

Slightly damp sand spreads, screeds, and compacts far more easily than bone dry sand, which just flows back into your screed lines. Lightly wetting the pile before you work it saves real effort.

Frequently Asked Questions

Click a question to see the answer

Answer

Is this the same as mason sand?

Yes, this is washed and finely screened sand, which is what most people mean when they ask for mason sand. It is finer and more uniform than concrete sand, which is what makes it workable for mortar mixing and paver joint filling.

Answer

How many cubic yards do I need for a paver patio?

One cubic yard covers about 324 square feet at a 1 inch depth, which is typical for joint filling. Measure your patio's square footage, decide on your fill depth between 1 and 2 inches, and divide accordingly to land on a cubic yard figure.

Answer

When is the best time to install sand for hardscaping in Georgetown?

Spring through fall is hardscape season here, before the first frost typically arrives around October 28. Working in that window gives mortar and joint sand time to set and settle before winter's freeze thaw cycles put stress on new paver work.

Answer

Where will the truck place the sand on delivery day?

Delivery is scheduled at checkout, and the driver will place the load wherever you indicate near your driveway or work area. Clear a spot ahead of time and let us know if there are access restrictions like narrow gates or low hanging branches.

Answer

Should I use this sand or chip stone for my paver base?

For joint filling and mortar, mason sand is still the right choice due to its fine, uniform grain. For the base layer under pavers, many contractors now prefer chip stone since it drains better and does not pump or wash out under heavy rain the way sand can.

More delivery around Georgetown, Kentucky

All Georgetown, Kentucky landscape supply