• Marshfield WI Sand Delivery - Mulch Mound
  • Marshfield WI Sand Delivery - Mulch Mound
1 2
Sand - Mulch Mound
Sand - Mulch Mound

About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.
Bill Doege
Bill Doege
Google Review

At a 1 inch depth, one cubic yard covers about 324 square feet, which is a useful starting point for paver joint fill or a pool base layer. For mortar mixing, order by volume needed for the mix ratio rather than by square footage, since it is not spread flat. Most residential jobs, patios, small walkways, pool base prep, land somewhere between a half yard and two yards.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

FAQs

Read all FAQs

Marshfield Sand Delivery

Marshfield Sand Delivery

4.7
137 reviews
$74.00 per Yard
$74.00
Sale Sold out
Shipping calculated at checkout.
Type
Size
Minimum of 3 Yard
Hand-picked local yards
4,000+ regional deliveries
Dedicated support
Why order through Mulch Mound

The best local sand, without the guesswork.

We hand-pick and partner with the best yards in your region, keep only the ones our buyers rate well, and back each load with our guarantee.

Mulch Mound Guarantee

If your sand isn't the quantity or quality you ordered, we'll make it right.

About this sand

Washed and finely screened masonry sand for mortar, paver joints, and pool bases. Consistent grain, ready to screed.
Bill Doege
Bill Doege
Google Review

At a 1 inch depth, one cubic yard covers about 324 square feet, which is a useful starting point for paver joint fill or a pool base layer. For mortar mixing, order by volume needed for the mix ratio rather than by square footage, since it is not spread flat. Most residential jobs, patios, small walkways, pool base prep, land somewhere between a half yard and two yards.

A yard is approximately 27 cubic feet. As a general guideline, one yard of material can cover an area of about 100-160 square feet at a 2-3 inch depth.

FAQs

Read all FAQs

View full details

How It Works

Getting started is easy — just follow these simple steps

1

Choose your quantity

Adjust the quantity to match your project. One cubic yard covers about 100 to 160 square feet at a 2 to 3 inch depth.

2

Select your delivery date

Select a delivery date you'd like for the product to be dropped off at your home

3

Sit back and wait

Sit back, wait, and let us work our magic to make sure the highest quality product is delivered to your driveway.

From The Mouths of Marshfield Folks

4.7
out of 5 based on 137 reviews
Google Reviews
Ryan Cully
Ryan Cully

First time going with this company for mulch and it was an efficient process from start to finish. Website was easy—I told them exactly where I wan...

Read full review

First time going with this company for mulch and it was an efficient process from start to finish. Website was easy—I told them exactly where I wanted the mulch put on my driveway, and it was delivered perfectly when I got home from work the next day. Best deal around when I compared it to competitors and I will definitely be becoming back.

Google Review

Complete Your Outdoor Project

Sand pairs with pavers, crushed stone base, and edging on most hardscape jobs, and many Marshfield crews are shifting to clean chip stone for paver bedding instead of sand since it will not pump out from under the pavers over a Wisconsin freeze thaw cycle. If you are pouring a pool base or mixing mortar, sand is still the right call, just keep bedding and jointing needs separate when you order.

Marshfield Soil Delivery
Marshfield Mulch Delivery
Mulch Mound Pro Tip

If you are filling paver joints in Marshfield, know that mason sand is being phased out for that job in favor of clean chip stone, because sand pumps out from under pavers during our freeze thaw cycles and leaves gaps by spring. Use mason sand for the mortar itself, but ask about chip stone for the joints if you want the paver surface to stay tight through winter.

Mulch Mound Pro Tip

Do not mix mortar sand in freezing temperatures, the water in the mix will not cure properly below about 40 degrees, which matters here given how early frost arrives in late September. Plan mortar work for the warmer stretch of the season and keep sand covered and dry on site so it does not pick up excess moisture before mixing.

Mulch Mound Pro Tip

Order sand and any base stone in the same delivery when possible, since separate trips cost more in fuel and time than combining a load. If your project needs both bedding material and mason sand for joints or mortar, figure both quantities before you check out so you are not paying for a second delivery over a small shortfall.

Working With Sand in Marshfield

Marshfield sits on silt loam, which drains slowly and holds water longer than sandy soil, so most sand delivered here is not going into the ground, it is going into a mix or a joint. With a growing season that runs from late May to late September, hardscape crews have a tight window to get patios, walkways, and pool decks built before frost returns in late September. Mason sand fills paver joints tight and works well in mortar for the brick and stone work common on older Marshfield homes. It is not the material for soil amendment here, silt loam does not need more fines.

Masonry vs Fill Sand

Masonry sand is washed and finely screened, the right choice for mortar work, paver joints, and sandboxes. Fill sand is coarser and less processed, better suited to leveling, bedding pipe, and filling low spots.

Bedding and Leveling

For pavers, screed a 1 inch sand bed over a compacted base rather than using sand to fix deep grade problems. A thin, even bed locks pavers in place. A thick one shifts underfoot.

Working With Moisture

Slightly damp sand spreads, screeds, and compacts far more easily than bone dry sand, which just flows back into your screed lines. Lightly wetting the pile before you work it saves real effort.

Frequently Asked Questions

Click a question to see the answer

Answer

What is mason sand actually used for on a home project in Marshfield?

It is mainly used for mixing mortar for brick or stone work and for filling joints between pavers. Some pool installers also use it as a smooth base layer under the pool liner. It is not meant for lawns, gardens, or drainage, our silt loam soil does not need more fine sand mixed into it.

Answer

How many cubic yards of sand do I need for a paver patio?

One cubic yard covers about 324 square feet at a 1 inch depth, which is more than enough for joint filling on most residential patios, since joints only need a thin layer worked into the gaps. A typical patio, 200 to 400 square feet, usually needs well under a full cubic yard just for jointing.

Answer

When is the best time to do sand and paver work in Marshfield?

Spring through fall, roughly late May through late September, is the real working window here given our last and first frost dates. Mortar will not cure well in cold temperatures, so plan mortar mixing jobs for warmer stretches and avoid late season pours that could get hit by an early frost.

Answer

Where will the sand be placed when it is delivered?

We drop it wherever you specify, driveway, curb, or job site, at the delivery date you choose during checkout. Make sure the area is clear and accessible for a truck, and if you need it moved further, plan for wheelbarrow access ahead of time.

Answer

Should I use mason sand or chip stone under my pavers?

Mason sand is the traditional choice, but many installers here are moving to clean chip stone for paver bedding because it resists shifting and does not pump out during freeze thaw cycles. Mason sand still makes sense for mortar mixing and joint fill, chip stone is worth asking about for the base layer itself.

More delivery around Marshfield, Wisconsin

All Marshfield, Wisconsin landscape supply