Really appreciate the care and follow thru that this company had with our order. A hiccup came up but they were quick to respond and address all concerns, which made our garden day a success! Thank you for your prompt care.
Thanks! We received your request.
Something went wrong. Please try again.
At a 1 inch depth, one cubic yard covers about 324 square feet, so a typical paver patio or pool deck border project might only need a fraction of a yard for joint filling, while a mortar mixing job depends on your batch ratios rather than square footage. Since it weighs in around 1.35 tons per cubic yard, even a modest order adds up in weight, so measure your joint area or mortar volume before ordering. Most Portland customers order this by the half yard or full yard depending on whether it is a small paver repair or a full mortar bed job.
Couldn't load pickup availability
We hand-pick and partner with the best yards in your region, keep only the ones our buyers rate well, and back each load with our guarantee.
If your sand isn't the quantity or quality you ordered, we'll make it right.
Really appreciate the care and follow thru that this company had with our order. A hiccup came up but they were quick to respond and address all concerns, which made our garden day a success! Thank you for your prompt care.
At a 1 inch depth, one cubic yard covers about 324 square feet, so a typical paver patio or pool deck border project might only need a fraction of a yard for joint filling, while a mortar mixing job depends on your batch ratios rather than square footage. Since it weighs in around 1.35 tons per cubic yard, even a modest order adds up in weight, so measure your joint area or mortar volume before ordering. Most Portland customers order this by the half yard or full yard depending on whether it is a small paver repair or a full mortar bed job.
Thanks! We received your request.
Something went wrong. Please try again.
Getting started is easy — just follow these simple steps
Adjust the quantity to match your project. One cubic yard covers about 100 to 160 square feet at a 2 to 3 inch depth.
Select a delivery date you'd like for the product to be dropped off at your home
Sit back, wait, and let us work our magic to make sure the highest quality product is delivered to your driveway.
Really appreciate the care and follow thru that this company had with our order. A hiccup came up but they were quick to respond and address all co...
Really appreciate the care and follow thru that this company had with our order. A hiccup came up but they were quick to respond and address all concerns, which made our garden day a success! Thank you for your prompt care.
I have ordered twice now, a pleasure to deal with, easy and fast delivery, beautiful mulch!
Highest compliments. Great driver.
Website is easy to navigate. Just a seamless process. 5 stars!!
Sand pairs naturally with pavers, flagstone, and any mortar based masonry work, and a lot of Portland crews are pairing it with clean chip stone instead for paver bedding since it handles wet freeze cycles without pumping out. If you are mixing mortar for a stone wall or fireplace surround near Powell's or anywhere in the older neighborhoods with brick facades, this is the grade to use. Keep a tarp or plywood staging area ready if you are combining it with cement on site.
Service area
For mortar work in Portland's damp climate, keep your sand covered with a tarp between mixing sessions. Volcanic loam sites often have poor natural drainage, so uncovered sand left on the ground here will pick up moisture fast, throwing off your water to sand ratio in the mix. A few extra minutes tarping the pile after each work session saves you from guessing at slump consistency the next morning.
A common mistake on paver jobs is using this sand as bedding under the pavers instead of just in the joints. Fine washed sand under pavers can pump up through joints during Portland's heavy winter rains, leaving gaps and uneven pavers by spring. Use it strictly for joint fill and mortar, and let coarser bedding material handle the structural layer beneath the pavers themselves.
If your project spans both mortar work and paver joints, order the full estimated volume in one delivery rather than splitting it into two trips, since the weight based cost per trip adds up fast with a material this dense. Pair it with chip stone for the bedding layer so you are only ordering this finer sand for the parts of the job that actually need it, mortar mixing and joint fill.
Portland sits on volcanic loam that holds moisture well, which is great for garden beds but not what you want under a patio or near a pool deck where drainage and stability matter more. This sand gives paver joints and mortar mixes a consistent, fine texture that the native loam cannot provide on its own. With the wet season running roughly November through March, most sand deliveries here land in the spring through fall build window when crews can actually get a slab or patio base to set up right. It is not a mulch or a soil amendment, it is a structural and jointing material for the hardscape side of a project.
Masonry sand is washed and finely screened, the right choice for mortar work, paver joints, and sandboxes. Fill sand is coarser and less processed, better suited to leveling, bedding pipe, and filling low spots.
For pavers, screed a 1 inch sand bed over a compacted base rather than using sand to fix deep grade problems. A thin, even bed locks pavers in place. A thick one shifts underfoot.
Slightly damp sand spreads, screeds, and compacts far more easily than bone dry sand, which just flows back into your screed lines. Lightly wetting the pile before you work it saves real effort.
